Whirlpools round

The round Pure SPA Bubble model from INTEX has an integrated limescale protection system. The smaller version offers space for 4 people, has an inside diameter of 145 cm (attention: outside diameter 196 cm), a height of 71 cm and a capacity of around 795 liters. The whirlpool heats up between 1.5 to 2.5 degrees per hour of heating time. The integrated bubble device with 800 watts of power and 120 air nozzles generate the bubbles already in the name of the model, which means pleasantly flowing water. The larger round model has 6 seats, an inner diameter of 165 cm (attention: outer diameter 216 cm) with a height of 71 cm and a capacity of almost 1100 liters. The integrated bubble device with 800 watts of power and 140 air nozzles make the water bubble.

8 Items

per page
Set Descending Direction
List Grid
  1. New
    Free shipping
    New
    Free shipping
    €989.00
    including 20% VAT
    Add to Wish List
  2. Bestseller
    Free shipping
    Bestseller
    Free shipping
    €799.00
    including 20% VAT
    Add to Wish List
  3. Free shipping
    Free shipping
    €829.00
    including 20% VAT
    Add to Wish List
  4. New
    Free shipping
    New
    Free shipping
    €799.00
    including 20% VAT
    Add to Wish List
  5. New
    Free shipping
    New
    Free shipping
    €859.00
    including 20% VAT
    Add to Wish List
  6. Free shipping
    Free shipping
    €799.00
    including 20% VAT
    Add to Wish List
  7. Free shipping
    Free shipping
    €899.00
    including 20% VAT
    Add to Wish List
  8. Bestseller
    New
    Free shipping
    Bestseller
    New
    Free shipping
    €649.00
    including 20% VAT
    Add to Wish List

8 Items

per page
Set Descending Direction

Frequently asked questions for Whirlpools round:

Switch off and unplug the control unit. Make sure that the cover grille of the filter cartridge unit is clean and free of obstructions. Clean or replace the filter cartridge, see section Maintenance and storage. Make sure that the inlet and outlet connections on the whirlpool and filter pump are not blocked. Ensure that the whirlpool water is properly disinfected to keep the filter cartridge clean and not clogged. 

If the ambient temperature is below 4ºC, we recommend not using the whirlpool. Switch off and unplug the control unit. Add some warm water to raise the water temperature of the whirlpool to over 5°C (41°F). Then press the button to heat the water to the desired temperature.

Switch off and unplug the control unit. When the water has cooled down, turn on the FI and restart everything. Turn off the heating. Then press the Filter and Bubble buttons to lower the water temperature. 

Switch off and unplug the control unit. Turn on the FI again and restart everything. 

Press the water filter button to activate the filter pump again. After 72 hours of continuous heating operation, the pump automatically switches to idle mode. The quick heating and water filtration functions are deactivated.

Remove the electrolytic storage cell for inspection and cleaning if necessary. Use salinity test strips to check the value of the water. Add salt. See “Salinity Information”. Make sure the cell's cable is securely plugged into the socket. Replace the memory cell if necessary.

If the salt content is too high, drain some of the pool water and fill it up with fresh water. Remove the electrolytic storage cell for inspection and cleaning if necessary. Use salinity test strips to check the value of the water. If the salt content is too high, drain some of the pool water and fill it up with fresh water. Make sure the cell's cable is securely plugged into the socket. If necessary, replace the memory cell.

Make sure that the air valve cap is tightly closed. Fill the spa with air, then make sure the air valve base is tightened properly, please refer to chapter "Spa air valve attachment". Wrinkles occur during storage or when the spa is folded. Very often the whirlpool is stored in colder rooms (e.g. cellar compartment, etc.). When the tub is inflated for the first time, the material requires a certain period of time to expand or to adapt to the ambient temperature. Therefore, the pool must be re-inflated several times when it is used for the first time. Spray some soapy water on the suspicious spot, if there is a crack or hole, bubbles will form at this spot. After you have been able to locate the leak, clean and dry the spot carefully and repair it with the repair kit provided.

Do not expose the spa to direct sunlight for a long period of time. Please check the air pressure and release some air if necessary. This procedure is very important, especially in hot weather, to avoid damage!

Check the pressure relief valve for leaks. Whirlpools from 2018 have a pressure relief valve. It is possible that the pressure relief valve does not seal due to dirt particles and does not close properly. As a result, air can escape there. Open the cap, unscrew the pressure relief valve with the wrench (included in the scope of delivery) and remove it, check it for dirt particles. Check the pressure spring and seal for accuracy of fit, carry out steps 1+2 in reverse order.

Tighten the inlet and outlet connections. Cover the O-ring with Vaseline to make it watertight. Remove the grille inside the spa with a screwdriver, make sure the inlet/outlet O-ring is in place, cleaned and not broken. Check the connections for cracks. Replace the defective parts if necessary. 

Plug the control unit directly into a socket and do not use extension cables or distributors. Check your house wiring for overload, the socket may have a defect. Contact a qualified electrician. Reset the residual current circuit breaker.

Make sure that the SPA is plugged in and turned on and that the control panel power plug is securely attached to the control unit. Check the power source and reset the FI switch.

Whirlpools round

A high-strength triple-laminated vinyl in combination with the patented Fiber-Tech© construction withstands even extreme loads. A powerful filter pump or a heater corresponding to the whirlpool size ensure crystal-clear and warm water. The lockable insulating cover included in the scope of delivery serves as a safety feature and reduces heating costs to a minimum.

Installation location

When choosing a suitable location for the round Pure SPA Bubble model from INTEX, please note that the inner diameter and outer diameter differ by 50 cm. The installation site must be level and be able to withstand the weight of the filled whirlpool tub. In order to avoid damage, please also take into account possible leaking water when choosing the location.